Contech-lighting CL8 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Contech-lighting CL8 herunter. ConTech Lighting CL8 User Manual Benutzerhandbuch

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 1
  • Inhaltsverzeichnis
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 0
For the ConTech Lighting 6” and 8” Ceiling Mount Integrated LED Cylinder Series: CL6 and CL8
INSTALLATION PROCEDURES
Before attempting installation please refer to your local electrical code.
1. Detach the cylinder lid from the fixture by twisting the lid clockwise and
pull it up.
2. Remove cylinder tether from lid and attach lid to junction box.
3. Re-attach cylinder tether to lid to aid wiring. Figure 1
4. Cylinder housing may contain multiple wires, depending upon dimming or
non-dimming option being installed.
5. Connect cylinder black (hot) wire to junction box hot wire, and connect
cylinder white (neutral) to junction box neutral wire. Connect cylinder
green ground wire to either junction box ground wire or ground screw.
6. For cylinders with 12D1 in catalog number [Standard Triac Dimming], the
driver can be dimmed with many quality 120V incandescent and
electronic low voltage dimmers without additional wiring.
7. For cylinders with MVD2 in catalog number (0-10V Dimming), the driver
can be dimmed with 0-10V dimming controls. Locate low voltage
dimming control wires (purple, gray) in cylinder and make appropriate
connections, purple to Dim+ junction box lead and gray to Dim- junction
box lead. For Non-Dimming applications, leave the dimming control wires
(purple and gray) capped inside the cylinder. Note: When using 0-10V
dimming drivers, Class I wiring (300V wiring inside conduit) is required.
Please consult factory for additional details.
8. For cylinders with 12D3 in catalog number, the driver (Lutron Hi-Lume
A-Series LTE) is compatible with various Lutron forward phase dimming
controls. Contact Lutron for the up-to-date compatibility list of dimming
controls: www.lutron.com. Also note for cylinders with 12D3 in catalog
number, an additional ground connection is required to ground the driver
case, ensure that the (2) two cylinder ground wires are either wired to
junction box ground wire or ground screw.
9. Be sure not to pinch wires when attaching cylinder to lid. Engage cylinder
to lid then turn cylinder counter-clockwise until it stops.
LED MODULE AND REFLECTOR INSTALLATION:
1. Remove protective cover from LED module.
2. Attach reflector to LED module by aligning tabs, then twist and lock into
place. Figure 2
3. Make the LED module electrical connection. Figure 3
4. Push LED module/reflector assembly into cylinder until reflector flange
seats firmly against cylinder face. Cylinder spring clips secure
module/reflector assembly in place.
5. For wet location installations: Attach gasketed trim ring with the four
(4) provided Philips head screws.
IMPORTANT SAFETY INSTRUCTIONS:
• Read all the instructions before installation. Save instructions for later use.
• Turn off power at fuse or circuit breaker box before installation or before doing any
maintenance work.
• Product must be grounded to avoid potential electric shock and any other potential
hazards.
• Product must be mounted in locations and at heights and in a manner consistent
with its intended use, and in compliance with National Electrical Code and local
codes. Use of accessory equipment is not recommended.
• Installing contrary to instructions may cause unsafe conditions.
• Do not block light from the trim aperture, in whole or in part, as this may cause
unsafe conditions.
• Warning: Risk of fire. Most dwellings built before 1985 have supply wire rated at
60°C. Consult a qualified electrician before installation.
• Avoid hazards to children: account for all parts and properly dispose of all packing
materials.
• Call the Technical Support department at Con-Tech Lighting with any installation
questions: 847.559.5500
LEDCYLINST CM
www.contechlighting.com
All specifications subject to change without notice.
1-847-559-5500 This document can be recycled.
Seitenansicht 0
1

Inhaltsverzeichnis

Seite 1 - INSTALLATION PROCEDURES

For the ConTech Lighting 6” and 8” Ceiling Mount Integrated LED Cylinder Series: CL6 and CL8INSTALLATION PROCEDURESBefore attempting installation plea

Verwandte Modelle: CL6

Kommentare zu diesen Handbüchern

Keine Kommentare